Fujitsu IDE hard drives Cmos stettings and jumper setting.

Fujitsu telephone numbers are:
TECH SUPPORT (408)-894-3950, Faxback (408)-428-0456.
All drives are listed in order from smallest to largest.
CAP=capacity of the hard drive, CYL=cylinder, HDS=heads, W/P=writeprecom, L/Z=landing zone,, SPT=secotrs, T=tables for jumper drive settings, (Drive jumper settings are listed @ the end of the hard drive list).


M2611T CAP= 40MB, CYL= 667, HDS= 4, W/P=0, L/Z= 667, SPT=33, T=1.
M2612T CAP= 45MB, CYL= 667, HDS= 8, W/P=0, L/Z= 667, SPT=33, T=1.
M2616T CAP=104MB, CYL= 977, HDS=12, W/P=0, L/Z= 977, SPT=17, T=1.
M2613T CAP=135MB, CYL= 667, HDS=12, W/P=0, L/Z= 667, SPT=33, T=1.
M2614T CAP=180MB, CYL= 667, HDS=16, W/P=0, L/Z= 667, SPT=33, T=1.
M2637T CAP=240MB, CYL= 698, HDS=12, W/P=0, L/Z= 698, SPT=56, T=2.
M2681T CAP=264MB, CYL= 977, HDS=11, W/P=0, L/Z= 977, SPT=48, T=3.
M2622T CAP=326MB, CYL=1013, HDS=10, W/P=0, L/Z=1013, SPT=63, T=4.
M2682T CAP=352MB, CYL= 992, HDS=11, W/P=0, L/Z= 992, SPT=63, T=3.
M2623T CAP=420MB, CYL=1002, HDS=13, W/P=0, L/Z=1002, SPT=63, T=4.
M2624T CAP=513MB, CYL= 995, HDS=16, W/P=0, L/Z= 995, SPT=63, T=4.
M2684T CAP=528MB, CYL=1024, HDS=16, W/P=0, L/Z=1024, SPT=63, T=3.
M1603T CAP=544MB, CYL=1055, HDS=16, W/P=0, L/Z=1055, SPT=63, T=3.
M1612T CAP=545MB, CYL=1057, HDS=16, W/P=0, L/Z=1057, SPT=63, T=3.
M1606T CAP=1.0 GB, CYL=2111, HDS=16, W/P=0, L/Z=2111, SPT=63, T=3.
M1614T CAP=1.0 GB, CYL=2114, HDS=16, W/P=0, L/Z=2114, SPT=63, T=3.

TABLE 1
SWITCH SETTINGS FOR SW2
SINGLE DRIVE - SWITCH 1 ON
MASTER DRIVE - SWITCH 1 & 3 ON
SLAVE DRIVE - SWITCH 2 & 3 ON

TABLE 2
JUMPER SETTINGS FOR CNH1
SINGLE DRIVE - NO JUMPERS INSTALLED
MASTER DRIVE - NO JUMPERS INSTALLED
SLAVE DRIVE - JUMPER PINS 2 & 4

TABLE 3
JUMPER SETTINGS FOR CNH1
SINGLE DRIVE - JUMPER PINS 1 & 2
MASTER DRIVE - JUMPER PINS 1 & 2
SLAVE DRIVE - NO JUMPERS INSTALLED

TABLE 4
SWITCH SETTINGS FOR SW1
SINGLE DRIVE - SWITCH 5 OFF
MASTER DRIVE - SWITCH 5 OFF
SLAVE DRIVE - SWITCH 5 ON

TABLE 2
DRIVE JUMPER SETTINGS
SINGLE DRIVE - JUMPER CD
MASTER DRIVE - JUMPER CD & DSP
SLAVE DRIVE - NO JUMPERS INSTALLED

TABLE 3
DRIVE JUMPER SETTINGS
SINGLE DRIVE - JUMPER CD
MASTER DRIVE - JUMPER CD
SLAVE DRIVE - NO JUMPERS INSTALLED

TABLE 4
DRIVE JUMPER SETTINGS
SINGLE DRIVE - JUMPER PINS 1 & 2
MASTER DRIVE - JUMPER PINS 1 & 2
SLAVE DRIVE - NO JUMPERS INSTALLED

---

Return to technical index, Return to MegaHaus home page