GVP A3001 Series II Accelerators
68030 CPU Board REV7 Jumper Settings
Jumper Default Description
J1 Shorted Reserved for future use
J2 OPEN Reserved for future use
J4 OPEN Connects 68882 FPU to oscillator US when shorted
J5 SHORTED Connects 68882 FPU to oscillator U1 when shorted
J6 OPEN Disables 68030 MMU when shorted
J7 ---->> OPEN for 50MHz clock speed and SHORTED for lower
clock speeds
J9 SHORTED Remove this jumper to enable the 68030 Boot code EPROMS
(U23 and U25) when these are installed
J10 SHORTED A2000 Motherboard type. Shorted for A2000 motherboards
REV4.0 and up (type B2000) Open for original 4-layer
German motherboard. When this jumper is left open the
68000 CPU must be removed.
J11 OPEN Disables 68030 CPU and bootup in 68000 mode when shorted
J12 OPEN SHORT to change clocking mode for compatibility with old
German A2000 motherboard
J13 OPEN SHORT to change clocking mode for compatibility with old
German A2000 motherboard
J14 SHORTED OPEN to change clocking mode for compatibility with old
German A2000 motherboard
J15 SHORTED OPEN to DISABLE the code contained in the Autoboot
EPROM (U34)
J16 SHORTED Reserved for diagnostic use
J17 SHORTED Set size of EPROM being used for "AT" Autoboot EPROM (U34)
SHORTED for 27256 type and OPEN for 27128 type
J18 SHORTED OPEN when an "AT" hard drive is connected to enable the
"AT" driver code in the Autoboot EPROM (U34). This jumper
is only relevant when using Autoboot EPROM v3 or later.
NOTE: J10, J12, J13 and J14 are a set and must be changed over at the same
time when installing into an A2000 with an old 4-layer German board.
68000 CPU must also be removed at the same time.
32-bit Wide A2000-RAM32 Rev 3 Jumper Settings
Jumper Default Description
J1 SHORTED Refresh rate
J2 OPEN Refresh rate
J3 ---->> Refresh rate, OPEN for 50MHz, Shorted for lower clock.
J4 SHORTED Refresh rate
J11 OPEN Refresh rate
J8 SHORTED Refresh enable
J6 SHORTED Reserved
CN11 ---->> All pins OPEN for 50MHz clock speed. SHORT pins 2 and 3
for lower clock speeds. Pin 1 indicated by arrowhead.
CN12 SHORT1-2 SHORT pins 1 and 2. Pein 1 indicated by arrowhead.
CN13 ---->> SHORT for 50MHz clock speed OPEN for lower.
J5 ---->> SHORTED when using only (up to 8) 1MB SIMMs. NOTE that
this is the only option supported for speeds below 50MHz
50MHz clock speed option only: OPEN when using FOUR 1 MB SIMMs in sockets
CN3-CN6 and up to FOUR 4 MB SIMMs in sockets CN7-CN10. Allows a maximum of
20MB 32-bit wide RAM.
RAM Settings
RAM SIZE RAM Type Qty RAM Location Jumper J5
2 SIMM32-1MB 2 CN3-CN4 On
4 SIMM32-1MB 4 CN3-CN6 On
8 SIMM32-1MB 8 CN3-CN10 On
8* SIMM32-1MB 4 CN3-CN6 Off
SIMM32-4MB 1 CN7 Off
12* SIMM32-1MB 4 CN3-CN6 Off
SIMM32-4MB 2 CN7-CN8 Off
16* SIMM32-1MB 4 CN3-CN6 Off
SIMM32-4MB 3 CN7-CN9 Off
20* SIMM32-1MB 4 CN3-CN6 Off
SIMM32-4MB 4 CN7-CN10 Off
* Note: These RAM settings require the use of the SIMM32-4MB which only
fuction in the 50MHz version of the '030 accelerator. It also requires
that jumper J5 be open.
BACK TO MAIN TECHNICAL PAGE
TO CATALOG
BACK TO NATIONAL AMIGA