Mac Expert 1995 Winter

home *** CD-ROM | disk | FTP | other *** search

/ Mac Expert 1995 Winter / Mac Expert - Winter 95.iso / Les fichiers / Communications / AppleTalk Remote access / Scripts ARA ƒ / GV PP Gold No Dialtone < prev next >

Wrap

Text File | 1994-06-29 | 6.6 KB | 357 lines | [mlts/slnk]

! ! AppleTalk Remote Access Script ! For use with Global Village PowerPort/GOLD /SILVER and /BRONZE ! ! 6/21/92 AN Added "pause 30" right after @LABEL 30 to fix a problem ! with the PowerBook hanging when AUTO_ANSWER was selected. ! Also changed all &F strings to &F&C1&D1. ! 6/13/92 AN Always save &C1&D1 to NVRAM in Bronze ! AN Fixed bug where PowerPort/Bronze was not being recognized ! 6/06/92 LAL ORIGINAL RELEASE ! xx/xx/xx CTC Changed script to TelePort format. ! ! ! @ORIGINATE @ANSWER ! ! Talk to the modem at 2400 bps. ! serreset 2400, 0, 8, 1 ! ! First recall the factory configuration ! settries 0 matchclr @LABEL 1 matchstr 1 3 "OK\13\10" write "AT&F&C1\13" matchread 30 inctries iftries 2 59 jump 1 ! ! Which PowerPort is in use? High Speed (961) or Low Speed (242)? ! @LABEL 3 Flush pause 10 matchclr matchstr 1 68 "242\13\10\13\10" matchstr 2 4 "961\13\10\13\10" matchstr 3 4 "1442\13\10\13\10" write "ATI0\13" matchread 60 note "Not a Global Village PowerPort." 2 jump 59 ! ! PowerPort Silver or Gold Continues Here ! settries 0 @LABEL 4 note "Initializing high speed PowerPort..." 2 ! ! Talk to the modem at 19,200 bps. ! serreset 19200, 0, 8, 1 ! ! &f - recall factory settings ! \q3 - Use RTS/CTS flow control in full-duplex mode ! \k0 - Enter command state but do not send break ! \j0 - Disable port rate adjust ! S0=0 - Don't answer calls ! E0 - Turn command echo off ! \n5 - enable v.42LAPM autoreliable ! %c0 - turn off MNP5 compression ! HSReset 0 1 0 0 0 1 settries 0 matchclr @LABEL 5 matchstr 1 6 "OK\13\10" write "AT&f\\k0\\j0\\q3e0s0=0\n5%c0\13" matchread 50 inctries iftries 2 59 jump 5 ! ! If speaker on flag is true, jump to label 8. Else turn off the speaker ! @LABEL 6 ifstr 2 8 "1" pause 5 matchstr 1 8 "OK\13\10" write "ATM0\13" matchread 30 jump 59 ! ! The modem is ready so enable answering, or originate a call ! @LABEL 8 pause 5 ifANSWER 30 note "Dialing ^1" 3 write "ATX1DT^1\13" ! @LABEL 9 matchstr 1 11 "CONNECT 1200\13\10" matchstr 2 12 "CONNECT 2400\13\10" matchstr 3 13 "CONNECT 4800\13\10" matchstr 4 19 "CONNECT 7200\13\10" matchstr 5 14 "CONNECT 9600\13\10" matchstr 6 20 "CONNECT 12000\13\10" matchstr 7 18 "CONNECT 14400\13\10" matchstr 8 50 "NO CARRIER\13\10" matchstr 9 50 "ERROR\13\10" matchstr 10 52 "NO DIAL TONE\13\10" matchstr 11 53 "BUSY\13\10" matchstr 12 54 "NO ANSWER\13\10" matchread 700 jump 59 ! ! Notice that all we do for different connect speeds is issue a ! "CommunicatingAt" command. Remember, we locked the interface speed ! to 19,200 bps so we don't want to reset the serial speed after we connect. ! CommunicatingAt tells ARA what the actual line speed is so that it ! can set it's timers appropriately. I guess your performance would be ! sub-optimal if you don't set this... ! @LABEL 11 note "Communicating at 1200 bps." 2 CommunicatingAt 1200 jump 15 ! @LABEL 12 note "Communicating at 2400 bps." 2 CommunicatingAt 2400 jump 15 ! @LABEL 13 note "Communicating at 4800 bps." 2 CommunicatingAt 4800 jump 15 ! @LABEL 19 note "Communicating at 7200 bps." 2 CommunicatingAt 7200 jump 15 ! @LABEL 14 note "Communicating at 9600 bps." 2 CommunicatingAt 9600 jump 15 ! @LABEL 20 note "Communicating at 12000 bps." 2 CommunicatingAt 12000 jump 15 ! @LABEL 18 note "Communicating at 14400 bps." 2 CommunicatingAt 14400 jump 15 ! ! Set CTS handshaking ON in the serial port (that's the 1 in the HSReset ! command below ) ! @LABEL 15 HSReset 0 1 0 0 0 1 ifANSWER 16 pause 30 @LABEL 16 exit 0 ! ! @ANSWER ! Set up the modem to answer ! @LABEL 30 write "ATS0=1\13" matchstr 1 31 "OK\13\10" matchread 30 jump 59 ! @LABEL 31 matchstr 1 32 "RING\13\10" matchstr 2 11 "CONNECT 1200\13\10" matchstr 3 12 "CONNECT 2400\13\10" matchstr 4 13 "CONNECT 4800\13\10" matchstr 5 19 "CONNECT 7200\13\10" matchstr 6 14 "CONNECT 9600\13\10" matchstr 7 20 "CONNECT 12000\13\10" matchstr 8 18 "CONNECT 14400\13\10" matchstr 9 50 "NO CARRIER\13\10" matchstr 10 50 "ERROR\13\10" matchstr 11 52 "NO DIAL TONE\13\10" matchstr 12 53 "BUSY\13\10" matchstr 13 54 "NO ANSWER\13\10" matchread 700 jump 31 ! @LABEL 32 userhook 1 note "Answering phone..." 2 jump 31 ! ! 50: error messages ! @LABEL 50 exit -6021 ! @LABEL 52 exit -6020 ! @LABEL 53 exit -6022 ! @LABEL 54 exit -6023 ! @LABEL 59 exit -6019 ! ! Hang up the modem ! @HANGUP @LABEL 60 settries 0 serreset 19200, 0, 8, 1 HSReset 0 1 0 0 0 1 @LABEL 61 ! SBreak pause 20 Flush ! prevent disconnect garbage write "\13" ! start on a clean line @LABEL 96 matchclr matchstr 1 97 "OK\13\10" write "AT\13" matchread 30 inctries iftries 3 59 jump 96 @LABEL 97 settries 0 @LABEL 98 matchclr matchstr 1 62 "OK\13\10" matchstr 2 62 "NO CARRIER\13\10" write "ATH\13" matchread 100 inctries iftries 3 59 jump 98 @LABEL 62 settries 0 ! ! recall the factory settings. (see note at top of script) ! @LABEL 63 matchclr matchstr 1 65 "OK\13\10" pause 15 write "AT&f&C1\\V2w1\\k0\\j0\\q3e0s0=0\n5%c0\13" matchread 50 inctries iftries 3 59 jump 63 ! @LABEL 65 exit 0 ! ! ! ! ------------------- POWERPORT/BRONZE ------------------- ! ! PowerPort Bronze Continues Here ! @LABEL 68 note "Initializing PowerPort/Bronze..." 2 matchclr matchstr 1 69 "OK\13\10" write "AT&C1&D1&W0&W1\13" pause 5 matchread 30 jump 59 ! ! Turn off local echo, ignore NO DIALTONE and BUSY ! @LABEL 69 matchclr matchstr 1 70 "OK\13\10" write "ATE0X3S0=0\13" pause 5 matchread 30 jump 59 ! ! If speaker on flag is true, jump to label 8. Else turn off the speaker ! @LABEL 70 ifstr 2 71 "1" pause 5 matchstr 1 71 "OK\13\10" write "ATM0\13" matchread 30 jump 59 ! ! The modem is ready so enable answering, or originate a call ! @LABEL 71 pause 5 ifANSWER 100 note "Dialing ^1" 3 write "ATDT^1\13" ! matchstr 1 72 "CONNECT 1200\13\10" matchstr 2 73 "CONNECT 2400\13\10" matchstr 3 50 "NO CARRIER\13\10" matchstr 4 50 "ERROR\13\10" matchstr 5 52 "NO DIALTONE\13\10" matchstr 6 53 "BUSY\13\10" matchstr 7 54 "NO ANSWER\13\10" matchread 700 jump 59 ! @LABEL 72 note "Communicating at 1200 bps." 2 serreset 1200, 0, 8, 1 jump 75 ! @LABEL 73 note "Communicating at 2400 bps." 2 serreset 2400, 0, 8, 1 ! ! @LABEL 75 ifANSWER 76 pause 30 @LABEL 76 exit 0 ! ! @ANSWER for PowerPort BRONZE ! Set up the modem to answer ! @LABEL 100 write "ATS0=1\13" matchclr matchstr 1 101 "OK\13\10" matchread 30 jump 59 ! @LABEL 101 matchstr 1 77 "RING\13\10" matchstr 2 72 "CONNECT 1200\13\10" matchstr 3 73 "CONNECT 2400\13\10" matchstr 4 50 "NO CARRIER\13\10" matchstr 5 50 "ERROR\13\10" matchstr 6 52 "NO DIALTONE\13\10" matchstr 7 53 "BUSY\13\10" matchstr 8 54 "NO ANSWER\13\10" matchread 700 jump 101 ! @LABEL 77 userhook 1 note "Answering phone..." 2 jump 101 !