home *** CD-ROM | disk | FTP | other *** search
/ MPC Wizard 3.0 / WIZARD3_0.ISO / drivers / graf_p_z / tsng_w32 / readme.doc < prev    next >
Text File  |  1994-09-18  |  4KB  |  95 lines

  1. Tseng Labs can be reached at (215) 968-0502.
  2.  
  3.     ET4000/W32/W32i/W32p Windows 3.1 Video Driver Installation Instructions
  4.  
  5.                 ** IMPORTANT **
  6.  
  7. The drivers named "ET4-W32" in the Windows Setup use the ET4000/W32 accelerator
  8. features. The remaining drivers supplied are the same as used on the ET4000/AX.
  9.  
  10. This driver disk is designed to allow you to select or change the video driver
  11. for Windows 3.1 using Windows Setup. Setup can be executed from within Windows,
  12. or from DOS. Note that these driver files are in Microsoft compressed format
  13. and can only be accessed and executed by installing through Windows Setup.
  14. Simply copying the files into your \Windows\System subdirectory WILL NOT work
  15. and may corrupt your Windows installation. Installing the drivers correctly is,
  16. however, a simple process.
  17.  
  18. It is accomplished by following these instructions:
  19.  
  20. Installation from floppy disk
  21.  
  22. 1) Insert your Driver Disk in the appropriate floppy drive.
  23.  
  24. 2) From your Windows directory, type SETUP and select DISPLAY to change the
  25. video driver. Or, with Windows running, select Setup from the Program Manager
  26. Main group. Refer to your Microsoft Windows User's Guide for assistance in
  27. running Setup from inside Windows.
  28.  
  29. 3) Select "Other disk..." to direct the program to the floppy disk holding the
  30. new drivers. Note that after the drivers are installed, you will not have to
  31. select "Other disk..." again should you decide to change resolutions. Look for
  32. the ET4000-based drivers in the Display selection menu to select the display
  33. resolution you want.
  34.  
  35. 4) When asked where the drivers will be found, state the following:
  36.  
  37.     A:\
  38.  
  39. Follow instructions 6-7 below.
  40.  
  41.  
  42. Installation from Hard Disk
  43.  
  44. 1) Having the drivers loaded on the hard disk will make it easier and faster
  45. to change resolutions in the future. Make a subdirectory to hold the driver
  46. files.
  47.  
  48. example: C:>md \et4drv
  49.  
  50.     and switch to that subdirectory (C:>cd \et4drv)
  51.  
  52. 2) Insert the drivers disk into the appropriate drive and type the following
  53. command:
  54.  
  55.     COPY A:\*.*
  56.  
  57. 3) From your Windows directory, type SETUP and select DISPLAY to change the
  58. video driver. Or, with Windows running, select Setup from the Program Manager
  59. Main group. Refer to your Microsoft Windows User's Guide for assistance in
  60. running Setup from inside Windows.
  61.  
  62. 4) Select "Other disk..." to direct the program to the subdirectory holding the
  63. new drivers. Note that once the drivers are installed, you should not have to
  64. select "Other" again should you decide to change resolutions. Look for the
  65. ET4000-based drivers in the Display selection menu to select the display
  66. resolution you want.
  67.  
  68. 5) When asked where the drivers will be found, state the following (deleting
  69. what the program has displayed in the input window):
  70.  
  71.     [drive:]\[directory]
  72.  
  73.     e.g.: C:>\et4drv
  74.  
  75. 6) A standard Windows selection menu will appear with additional video drivers
  76. from which to select.
  77.  
  78. 7) Proceed normally through the remainder of the process. Check Microsoft
  79. Windows installation procedures if necessary.
  80.  
  81. 8) If you are having problems installing these drivers please contact your 
  82. board vendor for further assistance.(as your vendor may have done proprietary
  83. enhancements that require custom drivers)
  84.  
  85. Also, the included are Tseng HiColor/TrueColor drivers for 32K, 65K and 16Mil.
  86. simultaneous colors. If you attempt to run Microsoft Windows with a driver for
  87. which your display board cannot support, a brief message will appear in the
  88. upper left of your screen 
  89.  
  90.     "video driver unable to set desired mode"
  91.  
  92. before returning you back to the DOS prompt. If this occurs simply, run the
  93. SETUP program again and choose a supported display mode.
  94.  
  95.