home *** CD-ROM | disk | FTP | other *** search
-
- Design It (tm) Wearables
-
- Project Supples Moon Shirt Supplies
- --------------- -------------------
- 1 Can DESIGN-IT 1 Bottle white pearlized craft paint
- 1 Bottle CLEAN-IT 1 Small container silver glitter
- 1 Small container iridescent glitter
- GENERAL SUPPLIES
- ---------------- "SUN" Shirt Decorative Supplies
- plastic sheet -------------------------------
- Blue T- Shirt 2, 5/8" diameter gem stones (yellow orange)
- Paper Towels 1 Small container warm gold glitter
- #8 flat paint brush 1 bottle Black Paint
- 6" plastic plate for pattern 1 Small cantainer pumpkin glitter
- Sheet cardboard (size of shirt body) 1 Bottle "Kings Gold" paint
- Apron (optional) 1 Bottle "Coronation Russet" paint
- Pair Latex gloves (optional)
- Piece of chalk
- Straight Pins
-
- HELPFUL HINTS FOR "MOON" AND "SUN" SHIRTS
-
- 1. Practice applying DESIGN-IT on paper towel, making the moon, star,
- clouds, and sun rays.
- Always pull can toward yourself. A VERY THIN LINE IS BEST. Wipe tip
- frequently with paper towel moistened with CLEAN-IT.
- 2. Tightly secure shirt to board using straight pins. Smooth wrinkles.
-
- "MOON" SHIRT DIRECTIONS
-
- 1. Lay plate in center of T- shirt; where you wish design. Trace from top,
- around to left of plate, down and back up to approximately 4:00 o'clock
- spot, (see photograph).
- 2. Finish moon shape. Add clouds by drawing loose, sketchy lines with chalk,
- and make a large star near the moon. (see photograph)
- 3. Using DESIGN-lT' outline moon, stat and clouds. Set aside to dry 15 minutes.
- 4. Clean valve and craft tip with CLEAN-IT.
- 5. On shirt, brush around moon shape, clouds, and star with pearlired paint.
- 6. Paint moon and glitter with silver while paint is wet. Glitter clouds and
- star iridescent.
-
- "SUN" SHIRT DIRECTIONS
-
- 1. With chalk, trace a circle around plate onto fabric. Lightly draw 3"
- lines (sun rays) from edge of circle. Draw eyes, nose, and mouth.
- (see photograph)
- 2. With DESIGN-IT starting at top of circle, sparingly outline circle, eyes,
- nose and mouth. Add tiny dot of DESIGN-IT for pupil of each eye. Place
- gemstone into wet DESIGN-IT.
- 3. Starting at circle and following chalk marks slowly make rays with
- DESIGN-IT. Between the 3 rays add shorter rays of DESIGN-IT. Dry about
- 1 hour.
- 4. Clean craft tip and valve thoroughly with CLEAN-IT.
- 5. Paint all DESIGN-lT' lines with basecoat of "Coronation Flusset". Brush
- "Kings Gold" lightly over base coat. While paint is wet, sprinkle on a
- mixture of gold and pumpkin glitter.
- 6. Add dot of black paint to center of eyes.
- 7. Paint fine wiggly lines of "Coronation Russet" on fabric for additional
- rays. Dry thoroughly.
-
- GENERAL DlRECTIONS
-
- 1. Protect work surface with plastic or large trash bag.
- 2. Wear latex or plastic gloves and apron to protect nail polish and clothing.
- 3. Use at room temperature.
- 4. Apply a small amount ot DESIGN-lT'at a time.
- 5. DESIGN-IT is a permanent adhesive and bonds to everything when wet,
- except some plastic, like trash bags. Remove immediately from skin when wet
- with CLEAN-IT.
- 6. To reuse valve and craft tip: Clean them frequently with CLEAB-IT. Renove
- craft top and drip CLEAN-IT through it. Squirt CLEAN-IT into valve and
- empty residue on paper towel.