home *** CD-ROM | disk | FTP | other *** search
- % Computer Modern Math Symbols 8 point
- if unknown cmbase: input cmbase fi
-
- font_identifier:="CMSY"; font_size 8pt#;
-
- u#:=17/36pt#; % unit width
- width_adj#:=0pt#; % width adjustment for certain characters
- serif_fit#:=0pt#; % extra sidebar near lowercase serifs
- cap_serif_fit#:=4.1/36pt#; % extra sidebar near uppercase serifs
- letter_fit#:=0pt#; % extra space added to all sidebars
-
- body_height#:=216/36pt#; % height of tallest characters
- asc_height#:=200/36pt#; % height of lowercase ascenders
- cap_height#:=196.8/36pt#; % height of caps
- fig_height#:=185.6/36pt#; % height of numerals
- x_height#:=124/36pt#; % height of lowercase without ascenders
- math_axis#:=72/36pt#; % axis of symmetry for math symbols
- bar_height#:=69.6/36pt#; % height of crossbar in lowercase e
- comma_depth#:=56/36pt#; % depth of comma below baseline
- desc_depth#:=56/36pt#; % depth of lowercase descenders
-
- crisp#:=8/36pt#; % diameter of serif corners
- tiny#:=8/36pt#; % diameter of rounded corners
- fine#:=7/36pt#; % diameter of sharply rounded corners
- thin_join#:=7/36pt#; % width of extrafine details
- hair#:=9/36pt#; % lowercase hairline breadth
- stem#:=21.5/36pt#; % lowercase stem breadth
- curve#:=25/36pt#; % lowercase curve breadth
- ess#:=23/36pt#; % breadth in middle of lowercase s
- flare#:=26.5/36pt#; % diameter of bulbs or breadth of terminals
- dot_size#:=32/36pt#; % diameter of dots
- cap_hair#:=9.5/36pt#; % uppercase hairline breadth
- cap_stem#:=25.5/36pt#; % uppercase stem breadth
- cap_curve#:=29/36pt#; % uppercase curve breadth
- cap_ess#:=26/36pt#; % breadth in middle of uppercase s
- rule_thickness#:=.36pt#; % thickness of lines in math symbols
-
- dish#:=1/36pt#; % amount erased at top or bottom of serifs
- bracket#:=16/36pt#; % vertical distance from serif base to tangent
- jut#:=24/36pt#; % protrusion of lowercase serifs
- cap_jut#:=29/36pt#; % protrusion of uppercase serifs
- beak_jut#:=8.4/36pt#; % horizontal protrusion of beak serifs
- beak#:=56/36pt#; % vertical protrusion of beak serifs
- vair#:=8/36pt#; % vertical diameter of hairlines
- notch_cut#:=8pt#; % maximum breadth above or below notches
- bar#:=9.5/36pt#; % lowercase bar thickness
- slab#:=9.5/36pt#; % serif and arm thickness
- cap_bar#:=9.5/36pt#; % uppercase bar thickness
- cap_band#:=9.5/36pt#; % uppercase thickness above/below lobes
- cap_notch_cut#:=8pt#; % max breadth above/below uppercase notches
- serif_drop#:=3.2/36pt#; % vertical drop of sloped serifs
- stem_corr#:=1/36pt#; % for small refinements of stem breadth
- vair_corr#:=1/36pt#; % for small refinements of hairline height
- apex_corr#:=0pt#; % extra width at diagonal junctions
-
- o#:=6/36pt#; % amount of overshoot for curves
- apex_o#:=6/36pt#; % amount of overshoot for diagonal junctions
-
- slant:=.25; % tilt ratio $(\Delta x/\Delta y)$
- fudge:=1; % factor applied to weights of heavy characters
- math_spread:=.4; % extra openness of math symbols
- superness:=1/sqrt2; % parameter for superellipses
- superpull:=1/6; % extra openness inside bowls
- beak_darkness:=11/30; % fraction of triangle inside beak serifs
- ligs:=2; % level of ligatures to be included
-
- square_dots:=false; % should dots be square?
- hefty:=false; % should we try hard not to be overweight?
- serifs:=true; % should serifs and bulbs be attached?
- monospace:=false; % should all characters have the same width?
- variant_g:=true; % should an italic-style g be used?
- low_asterisk:=false; % should the asterisk be centered at the axis?
- math_fitting:=true; % should math-mode spacing be used?
-
- % the following font parameters are explained in {\sl The \TeX book}, Appendix G
- subs:=6/8; % subscripts to 8pt will normally be in 6pt type
- rth#:=.4pt#; % assume that rules will come from cmex10
- fontdimen 8: % parameters $\sigma_8$ through $\sigma_{22}$ will now be listed
- math_axis#+3.51rth#+36/36pt#+subs*desc_depth#, % num1
- math_axis#+1.51rth#+24/36pt#, % num2
- math_axis#+1.51rth#+38/36pt#, % num3
- -(math_axis#-3.51rth#-subs*fig_height#-98/36pt#), % denom1
- -(math_axis#-1.51rth#-subs*fig_height#-24/36pt#), % denom2
- 7.49pt#-subs*asc_height#, % sup1
- 6.99pt#-subs*asc_height#, % sup2
- 82/36pt#, % sup3
- 36/36pt#, % sub1
- 72/36pt#, % sub2
- subs*asc_height#-36/36pt#, % sup\_drop
- 18/36pt#, % sub\_drop
- 11.9pt#, % delim1
- 9.1pt#, % delim2
- math_axis#; % axis\_height
-
- generate mathsy % switch to the driver file
-