home
***
CD-ROM
|
disk
|
FTP
|
other
***
search
/
Magazyn Internet 2000 December
/
MICD_2000_12_NR1.iso
/
Dreamnet
/
drivery
/
SMC
/
pci_55.exe
/
NDIS
/
PCNFS.DOC
< prev
next >
Wrap
Text File
|
1997-12-05
|
5KB
|
160 lines
SMC
Sun PCNFS
For EtherPower, EtherPower^2, and the EtherPower 10/100 Family
of PCI Network Cards
INSTALLATION GUIDE
This software is licensed by SMC for use by its customers only.
Copyright (c) 1997 SMC Networks, Inc.. All rights reserved.
This installation guide:
o Supported network cards
o Using EZStart to copy the driver files
o Preparing your operating system
SUPPORTED NETWORK CARDS
o EtherPower Ethernet network cards
(SMC8432 board types)
o EtherPower^2 Dual-Channel Ethernet network cards
(SMC8434 board types)
o EtherPower 10/100 Fast Ethernet 100BASE-TX network cards
(SMC9332DST board type)
o EtherPower 10/100 Fast Ethernet 100BASE-TX network cards
(SMC9332BDT board type)
o EtherPower 10/100 Dual-Channel
Fast Ethernet 100BASE-TX network cards
(SMC9334BDT board type)
o EtherPower 10/100 Fast Ethernet 100BASE-T4 network cards
(SMC9332BVT board type)
USING EZSTART TO COPY THE DRIVER FILES
You can run EZStart from the SuperDisk or, for faster operation, you
can copy it onto a hard disk and run it from there. To run EZStart
from the hard disk, all files must be copied from the SuperDisk to
your computer's hard disk.
EZStart may copy files back to the SuperDisk to create an installation
diskette. Please make a backup copy of your SuperDisk before using
EZStart.
1. Insert the SuperDisk into a floppy disk drive.
2. Change to the floppy drive where the SuperDisk is installed.
3. To run EZStart from the DOS command line, type:
[path]ezstart<Enter>
To run EZStart in text mode (instead of graphics mode), type
[path]ezstart/T<Enter>
To run EZStart from Microsoft Windows v3.x:
select the 'File' menu in 'Program Manager'. When the 'Run'
dialog box appears, type:
[path]ezstart
in the 'Command Line' box, then select the 'OK' button.
To run EZStart with Windows 95:
1. Select 'Shut Down' from the 'Start' menu
2. Select the option to 'Restart the computer in MS-DOS mode'
NOTE: Do not run EZStart from a DOS window!
To run EZStart with Windows NT or OS/2:
EZStart does not run under these operating systems. Instead, boot
your computer using an MS-DOS operating system.
4. Select 'Custom' from the EZStart main screen.
5. Select 'Drivers/Documents' from the 'Custom Installation' screen.
6. There are two 'Network Drivers and Documentation Selection'
screens. Select the appropriate vendor from the first screen. The
screen appears again. Select the appropriate driver you wish to
install (make sure the selection you want is highlighted). Then
press the 'Enter' key or select 'OK'.
7. At the 'Network Drivers and Documentation' screen, the default
destination directory and a list of files to be copied to the
default directory are displayed. To accept the default destination
directory, select 'Copy Files'. Otherwise, enter a destination
directory at the prompt and select 'Copy Files'.
8. Follow the prompts to continue the installation.
9. Select 'Exit' to exit EZStart.
10. Remove the SuperDisk from the floppy disk drive.
PREPARING YOUR OPERATING SYSTEM
For driver setup and configuration instructions, refer to the
documentation provided with the Sun PCNFS network operating system.
Below are sample CONFIG.SYS, PROTOCOL.INI and AUTOEXEC.BAT files.
PROTOCOL.INI
[PROTOCOL MANAGER]
drivername=PROTMAN$
[SMC]
DRIVERNAME=SMCPWR$
[NFS-NDIS]
drivername=NFSLINK$
BINDINGS=SMC
CONFIG.SYS
DEVICE = C:\NFS\PCNFS.SYS
DEVICE = C:\NFS\SOCKDRV.SYS
DEVICE = C:\NFS\PROTMAN.SYS /I:C:\NFS
DEVICE = C:\NFS\SMCPWR.DOS
DEVICE = C:\NFS\NFS-NDIS.SYS
LASTDRIVE = V
AUTOEXEC.BAT
SET TZ = EST5EDT
SET PATH = C:\NFS;%PATH%
SET NFSDRIVE = C
PRT *
C:\NFS\NETBIND
# C:\NFS\NFSRUN # FOR VERSION 3.5 OF PC-NFS.
C:\NFS\NETINIT # FOR VERSION 4.0 AND ABOVE OF PC-NFS.
This commercial computer software and documentation is provided with
RESTRICTED RIGHTS. Use, duplication, or disclosure by the
Government is subject to restrictions set forth in subparagraph
(c) (1) (ii) of the Rights in Technical Data and Computer Software
clause at DFARS 252.227-7013, or subparagraphs (c) (1) and (2) of the
Commercial Computer Software -- Restricted Rights clause at
FAR 52.227-19, or Alternate III of the Rights in Data -- General
clause at FAR 52.227-14, as applicable. The manufacturer /
subcontractor is SMC Networks, Inc., 350 Kennedy,
Hauppauge, NY 11788.
SMC is a registered trademark; and EtherPower, EtherPower^2,
EtherPower 10/100, EZStart, and SuperDisk
are trademarks of SMC Networks, Inc.. Other product and
company names are registered trademarks or trademarks of their
respective holders.