<Chapter><Head>Safety Instructions and Regulatory Notices</Head>
<Para><Emphasis>BEFORE YOU START INSTALLATION OR USE OF THIS PRODUCT, CAREFULLY READ THESE INSTRUCTIONS</Emphasis> </Para><Warning>
<Para> <Emphasis>When using this product, always follow the basic safety precautions to reduce the risk of fire, electric shock and injury to persons, including the following:</Emphasis> </Para>
<List><ListItem><Para>Always install the product as described in the documentation that is included with your product.</Para></ListItem>
<ListItem><Para>Avoid using this product during an electrical storm. There may be a remote risk of electric shock from lightning.</Para></ListItem>
<ListItem><Para>Do not use this product to report a gas leak in the vicinity of the leak.</Para></ListItem></List></Warning>
<Section show = "wlan"><Head>Wireless</Head>
<Para>In case this product is equipped with a wireless transceiver, it uses Direct Sequence Spread Spectrum (DSSS) /Orthogonal Frequency Division Modulation (OFDM) radio technology. As such it is designed to be inter-operable with any other wireless DSSS/OFDM type product that:</Para>
<List><ListItem><Para>Complies with the IEEE802.11b/IEEE802.11g/IEEE802.11n Standard on Wireless LANs, as defined and approved by the Institute of Electrical and Electronics Engineers.</Para></ListItem>
<ListItem><Para>Is Wi-Fi® CERTIFIED™ as defined by the Wi-Fi® Alliance.</Para></ListItem></List></Section>
<Section><Head>Directive</Head>
<Para>Unless express and prior approval by THOMSON in writing, you may not:</Para>
<List><ListItem><Para>Disassemble, de-compile, reverse engineer, trace or otherwise analyse the equipment, its content, operation, or functionality,</Para>
<Para>or otherwise attempt to derive source code (or the underlying ideas, algorithms, structure or organization) from the equipment,</Para>
<Para>or from any other information provided by THOMSON, except to the extent that this restriction is expressly prohibited by local law;</Para></ListItem>
<ListItem><Para>Copy, rent, loan, re-sell, sub-license, or otherwise transfer or distribute the equipment to others;</Para></ListItem>
<ListItem><Para>Modify, adapt or create a derivative work of the equipment;</Para></ListItem>
<ListItem><Para>Remove from any copies of the equipment any product identification, copyright or other notices;</Para></ListItem>
<ListItem><Para>Disseminate performance information or analysis (including, without limitation, benchmarks) from any source relating to the equipment.</Para></ListItem></List>
<Para>Such acts not expressly approved by THOMSON will result in the loss of product warranty and may invalidate the user's authority to operate this equipment<Condition show = "INT,US"> in accordance with FCC Rules</Condition>.</Para>
<Para>THOMSON disclaims all responsibility in the event of use that does not comply with the present instructions.</Para></Section>
<Section show = "INT,GB,IE"><Head>Environmental information - WEEE directive </Head><WEEE>
<Para>This symbol means that your inoperative electronic appliance must be collected separately and not mixed with the household waste.The European Union has implemented a specific collection and recycling system for which producers are responsible.</Para>
<Para>This appliance has been designed and manufactured with high quality materials and components that can be recycled and reused.</Para>
<Para>Electrical and electronic appliances are liable to contain parts that are necessary in order for the system to work properly but which can become a health and environmental hazard if they are not handled or disposed of in the proper way. Consequently, please do not throw out your inoperative appliance with the household waste.</Para>
<Para>If you are the owner of the appliance, you must deposit it at the appropriate local collection point or leave it with the vendor when buying a new appliance.</Para>
<List><ListItem><Para>If you are a professional user, please follow your supplier's instructions.</Para></ListItem>
<ListItem><Para>If the appliance is rented to you or left in your care, please contact your service provider.</Para></ListItem></List></WEEE>
<Para><Emphasis>Please help us protect the environment in which we live!</Emphasis></Para></Section>
<Section><Head>Safety Instructions</Head>
<Block><Head>Climatic conditions</Head>
<Para>This product:</Para>
<List><ListItem><Para>Is intended for in-house stationary desktop use; the maximum ambient temperature may not exceed 40°C<Condition show = "INT,US,CA"> (104°F)</Condition>.</Para></ListItem>
<ListItem><Para>Must not be mounted in a location exposed to direct or excessive solar and/or heat radiation.</Para></ListItem>
<ListItem><Para>Must not be exposed to heat trap conditions and must not be subjected to water or condensation.</Para></ListItem>
<ListItem><Para>Must be installed in a Pollution Degree 2 environment (Environment where there is no pollution or only dry, nonconductive pollution).</Para></ListItem></List></Block>
<Block><Head>Cleaning</Head>
<Para>Unplug this product from the wall socket and computer before cleaning. Do not use liquid cleaners or aerosol cleaners. Use a damp cloth for cleaning.</Para></Block>
<Block><Head>Water and moisture</Head>
<Para>Do not use this product near water, for example, near a bathtub, washbowl, kitchen sink, laundry tub, in a wet basement or near a swimming pool. Transition of the product from a cold environment to a hot one, may cause condensation on some of its internal parts. Allow it to dry by itself before re-starting the product.</Para></Block>
<Block><Head>Interface classifications</Head>
<Para>The external interfaces<Condition hide = "ST110g,ST120g,ST121g,ST330pt,ST330sl,ST330v4"> on the rear panel</Condition> of the product are classified as follows:</Para>
<List><ListItem hide = "ST110g,ST120g,ST121g,ST180"><Para>DSL, <Condition hide = "shdsl,vdsl">ADSL, </Condition><Condition show = "shdsl">SHDSL, </Condition><Condition show = "vdsl">VDSL, </Condition>Line: TNV circuit, subjected to over voltages (TNV-3)</Para></ListItem>
<ListItem show = "isdn"><Para>ISDN: SELV circuit</Para></ListItem>
<ListItem show = "voice"><Para>PSTN, FXO: TNV circuit, subjected to over voltages (TNV-3)</Para></ListItem>
<ListItem show = "voice"><Para>Phone, VoIP, FXS: TNV circuit, not subjected to over voltages (TNV-2)</Para></ListItem></List><Warning show = "voice">
<Para><Emphasis>WARNING</Emphasis></Para>
<List><ListItem><Para>The Phone, VoIP, FXS port will be classified as a <Emphasis>TNV-3</Emphasis> circuit when connected internally to the PSTN, FXO port, for example, when the device is powered off.</Para></ListItem>
<ListItem><Para>If the product is equipped with a USB interface (slave and/or master) or any type of connector with metallic shielding, then it is not allowed to connect the Phone, VoIP, FXS port with the PSTN, FXO or the DSL, <Condition hide = "shdsl,vdsl">ADSL, </Condition><Condition show = "shdsl">SHDSL, </Condition><Condition show = "vdsl">VDSL, </Condition>Line port by any means, for example with an external telephone cable.</Para></ListItem></List></Warning>
<List><ListItem hide = "ST330pt,ST330sl,ST330v4"><Para>All <Condition hide = "ST110g,ST120g,ST121g,ST180">other </Condition>interface ports (e.g. Ethernet, 10/100Base-T/MDI(-X), <Condition show = "usb,ST120g,ST121g">USB, </Condition><Condition show = "ST610"></Condition><Condition show = "ST605,ST608,ST608WL,ST620">Console, Craft, </Condition>etc.)<Condition hide = "ST110g,ST120g,ST121g">, including the low voltage power input from the AC mains power supply</Condition>: SELV circuits.</Para></ListItem></List></Block>
<Block><Head>Electrical powering</Head>
<Para>The powering of the product must adhere to the power specifications indicated on the marking labels.</Para>
<Para hide = "ST110g,ST120g,ST121g,ST330pt,ST330sl,ST330v4">The power supply must be Class II and a Limited Power Source in accordance with the requirements of IEC60950-1/ EN60950-1, Clause 2.5 and rated as indicated on the label on your product. It must be tested and approved to national or local standards.</Para>
<Para show = "INT,US,CA" hide = "ST110g,ST120g,ST121g,ST330pt,ST330sl,ST330v4"><Emphasis>For US and Canada</Emphasis>: This product is intended to be supplied by a Listed Direct Plug-in<Condition show = "INT,US,CA">, or Desktop</Condition> Power Unit marked "Class 2" and rated as indicated on the label on your product.</Para>
<Para hide = "ST110g,ST120g,ST121g,ST330pt,ST330sl,ST330v4">The use of other types of supplies is prohibited. If you are not sure of the type of power supply needed, consult the product's user documentation or contact your local product dealer.</Para></Block>
<Block show = "INT,US,CA"><Head show = "isdn">ISDN</Head><Warning show = "isdn">
<Para><Emphasis>WARNING</Emphasis></Para>
<Para><Emphasis>For US and Canada</Emphasis>: Do not use the ISDN port; do not attempt to connect this port to the network at anytime.</Para></Warning></Block>
<Block show = "usb,ST120g,ST121g,ST330pt,ST330sl,ST330v4"><Head>USB</Head>
<Para>The device is to be connected to an identified USB port complying with the requirements of a Limited Power Source.</Para></Block>
<Para>To reduce the risk of fire, use only No 26 AWG wire size or larger telecommunication line cord.</Para></Warning></Block>
<Para>Connect the telecommunication line cord only in the <Condition show = "voice">PSTN, FXO, </Condition>DSL, <Condition hide = "shdsl,vdsl">ADSL, </Condition><Condition show = "shdsl">SHDSL, </Condition><Condition show = "vdsl">VDSL </Condition>or Line port of the product. Never plug the telecommunication line cord in another receptacle of the product.</Para>
<Para>Follow the installation instructions in the sequence as outlined in the installation guide.</Para>
<Para>If telephone service is required on the same line, a central splitter or distributed filter(s) must be installed for optimal DSL performance.</Para>
<Para>Depending on your DSL configuration and type of splitter / filters, installation must be carried out by qualified service personnel. Consult your telephone service company or DSL service provider for instructions.</Para></Block>
<Para>The Direct Plug-in power supply<Condition show = "INT,US,CA">, or the plug on the power supply cord</Condition> serves as disconnect device. Be sure that the power socket outlet you plug the power supply into is easily accessible and located as close to the equipment as possible.</Para></Block>
<Block><Head>Overloading</Head>
<Para>Do not overload mains supply socket outlets and extension cords as this increases the risk of fire or electric shock.</Para></Block>
<Block><Head>Servicing</Head>
<Para>To reduce the risk of electric shock, do not disassemble this product. None of its internal parts are user-replaceable; therefore, there is no reason to access the interior. Opening or removing covers may expose you to dangerous voltages. Incorrect reassembly could cause electric shock if the appliance is subsequently used.</Para>
<Para>If service or repair work is required, take it to a qualified service dealer.</Para></Block>
<Block><Head>Damage requiring service</Head>
<Para>Unplug this product from the wall outlet and refer servicing to qualified service personnel under the following conditions:</Para>
<List><ListItem><Para>When the power supply or its plug are damaged.</Para></ListItem>
<ListItem><Para>When the attached cords are damaged or frayed.</Para></ListItem>
<ListItem><Para>If liquid has been spilled into the product.</Para></ListItem>
<ListItem><Para>If the product has been exposed to rain or water.</Para></ListItem>
<ListItem><Para>If the product does not operate normally.</Para></ListItem>
<ListItem><Para>If the product has been dropped or damaged in any way.</Para></ListItem>
<ListItem><Para>There are noticeable signs of overheating.</Para></ListItem>
<ListItem><Para>If the product exhibits a distinct change in performance.</Para></ListItem></List>
<Para>Immediately disconnect the product if you notice it giving off a smell of burning or smoke. Under no circumstances must you open the equipment yourself; you run the risk of electrocution.</Para></Block></Section>
<Section><Head>Regulatory Information</Head>
<Para>You must install and use this device in strict accordance with the manufacturer's instructions as described in the user documentation that is included with your product.</Para>
<Para>Before you start installation or use of this product, carefully read the contents of this document for device specific constraints or rules that may apply in the country where you want to use this product.</Para>
<Para show = "wlan">In some situations or environments, the use of wireless devices may be restricted by the proprietor of the building or responsible representatives of the organization.</Para>
<Para show = "wlan">If you are uncertain of the policy that applies on the use of wireless equipment in a specific organization or environment (e.g. airports), you are encouraged to ask for authorization to use this device prior to turning on the equipment.</Para>
<Para>THOMSON is not responsible for any radio or television interference caused by unauthorized modification of the device, or the substitution or attachment of connecting cables and equipment other than specified by THOMSON. The correction of interference caused by such unauthorized modification, substitution or attachment will be the responsibility of the user.</Para>
<Para>THOMSON and its authorized resellers or distributors are not liable for any damage or violation of government regulations that may arise from failing to comply with these guidelines.</Para></Section>
<Section show = "INT,GB,IE"><Head>Europe - European Union</Head>
<Block><Head>European Community Declaration of Conformity</Head><CE>
<Para>Hereby, THOMSON, declares that this product is in compliance with the essential requirements and other relevant provisions of Directive 1999/5/EC of the European Parliament and of the Council.</Para></CE>
<Para>This equipment can be used in all countries that are member of the European Union and that are member of the European Free Trade Association.</Para>
<Para>The Declaration of Conformity can be found on <Link ref = "http://www.thomson-broadband.com">www.thomson-broadband.com</Link>.</Para>
<Para show = "wlan">In case this product is equipped with a wireless transceiver:</Para>
<List show = "wlan"><ListItem><Para>it is restricted to indoor use only.</Para></ListItem>
<ListItem><Para>it complies with the basic restrictions and limits as defined in the European Council Recommendation (1999/519/EC) on the limitation of exposure of the general public to Electromagnetic fields.</Para></ListItem></List></Block></Section>
<Section show = "INT,CA"><Head>North-America - Canada</Head>
<Block><Head>Notification of Canadian Radio Frequency Interference Statement</Head>
<Para>This Class B digital apparatus complies with Canadian ICES-003.</Para>
<Para><Emphasis>NOTICE</Emphasis>: This product meets the applicable Industry Canada technical specifications.</Para>
<Para hide = "shdsl,ST110g,ST120g,ST121g,ST180"><Emphasis>NOTICE</Emphasis>: The ringer Equivalence Number (REN) for this terminal equipment is 0.1. The REN is an indication of the maximum number of devices allowed to be connected to a telephone interface. The termination on an interface may consist of any combination of devices subject only to the requirement that the sum of the RENs of all the devices does not exceed five.</Para></Block>
<Block show = "wlan"><Head>Canada - Industry Canada (IC)</Head>
<Para>In case this product is equipped with an IEEE802.11b/IEEE802.11g/IEEE802.11n wireless transceiver, complying with RSS 210 and/or RSS 213 of Industry Canada, operation is subject to the following two conditions:</Para>
<Procedure><Step><Para>This device may not cause harmful interference.</Para></Step>
<Step><Para>This device must accept any interference received, including interference that may cause undesired operation of the device.</Para></Step></Procedure></Block><Warning>
<Para>This equipment complies with IC radiation exposure limits set forth for an uncontrolled environment. This equipment should be installed and operated with minimum distance 20cm between the radiator and your body.</Para></Warning>
<Block show = "wlan"><Head>Restricted Frequency Band</Head>
<Para>In case this product is equipped with an IEEE802.11b/IEEE802.11g/IEEE802.11n wireless transceiver, it only uses channels 1 to 11 (2412 to 2462 MHz) on Canada territory.</Para></Block></Section>
<Section show = "INT,US"><Head>North-America - United States of America</Head>
<Block><Head>Federal Communications Commission (FCC) Radio Frequency Interference Statement</Head><FCC>
<Para>This device has been tested and found to comply with the limits for a Class B digital device, pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against such interference in a residential installation.</Para>
<Para>This equipment generates, uses and can radiate radio frequency energy. Operation is subject to the following two conditions:</Para>
<Procedure><Step><Para>This device may not cause harmful interference, and</Para></Step>
<Step><Para>This device must accept any interference received, including interference that may cause undesired operation.</Para></Step></Procedure></FCC>
<Para>If not installed and used in accordance with the instructions, it may cause harmful interference to radio communications. However, there is no guarantee that interference will not occur in a particular installation. If this equipment does cause harmful interference to radio or television reception, which can be determined by turning the equipment ON and OFF, the user is encouraged to try to correct the interference by one or more of the following measures:</Para>
<List><ListItem><Para>Reorient or relocate the receiving antenna.</Para></ListItem>
<ListItem><Para>Increase the separation between the equipment and receiver.</Para></ListItem>
<ListItem><Para>Connect the equipment into an outlet on a circuit different from that to which the receiver is connected.</Para></ListItem>
<ListItem><Para>Consult the dealer or an experienced radio/television technician for help.</Para></ListItem></List>
<Para>The FCC requires the user to be notified that any changes or modifications to this device that are not expressly approved by THOMSON may void the user's authority to operate the equipment.</Para>
<Para>Responsible Party: THOMSON Inc., 10330 North Meridian Street, Indianapolis, IN 46290 USA, (580) 634-0151.</Para>
<Para>This equipment complies with Part 68 of the FCC Rules.</Para>
<Para>The customer information required for Telephone Terminal Equipment ("TTE") approved for connection to the Public Switched Telephone Network ("PSTN"), pursuant to 47 CFR §68.218(b)(1) can be found at <Link ref = "http://www.speedtouch.com">www.thomson-broadband.com</Link>.</Para></Block>
<Block show = "wlan"><Head>RF-Exposure Statement</Head>
<Para>When the product is equipped with a wireless interface, then it becomes a mobile or fixed mounted modular transmitter and must have a separation distance of at least 20cm between the antenna and the body of the user or nearby persons. In practice, this means that the user or nearby persons must have a distance of at least 20cm from the modem and must not lean on the modem in case it is wall-mounted.</Para>
<Para>With a separation distance of 20cm or more, the M(aximum) P(ermissible) E(xposure) limits are well above the potential this module is capable to produce.</Para>
<Para>The transmitter shall not be collocated with other transmitters or antennas.</Para></Block>
<Block show = "wlan"><Head>Restricted Frequency Band</Head>
<Para>In case this product is equipped with an IEEE802.11b/IEEE802.11g/IEEE802.11n wireless transceiver, it may only use channels 1 to 11 (2412 to 2462 MHz) on U.S.A. territory.</Para></Block></Section></Chapter>
